New Multiplex cable works in conjunction with the DRB-III Emulator, adds coverage for Sprinter/Crossfire.Allows interface with our U-Scan OBD II diagnostic application.Allows flash reprogramming of the latest model year Chrysler vehicles.This hardware setup comes equipped with the addition of a J2534 HS CAN Pass-Thru interface.
#Drb3 emulator software#
Includes: DRB III Emulator Software, DRB III+ hardware interface, vehicle cable, USB cable, and software licence. Optional Multiplex Cable for Sprinter and Crossfire. This software package even comes with non-powertrain ECU programming files to enable reflashing everything from BCMs to sliding door modules. The DRB III Emulator software application now runs on your personal computer and interfaces with the DRB III+ hardware device to enable all the functions of the original Chrysler DRB III Scan Tool and more. You are recommended to own WITECH VCI POD ( SP179) which comes with DRB III software and works stably online.This is the exact scan tool software application used in Chrysler, Jeep, and Dodge dealerships to service non-CAN based vehicles from 1998-2007. There are MicroPod 2 Clone (SP271-C1) and WITECH VCI POD ( SP179) for diagnosing Chrysler.įor MicroPod 2 Clone (SP271-C1), you may get Enhanced DRB III Emulator to work or not to work sometimes, it is not stable. Thanks to Radius and myckee from for their good sharing.įor Chinese MicroPod 2 Clone, you can buy from. Once updated, disconnect the internet and change the date back to 1/1/17 for it to work.
So the instructions are good, but at least for me, I had to fix the date to the correct date to get the flexnet updates.
#Drb3 emulator windows#
Plugged in the pod, waited for windows to see it and make the virtual network, and then launched witech. Then I followed the rest of the instructions. As soon as both had updated, I disconnected internet and then changed date back to 1/1/17.
#Drb3 emulator update#
Now flexnet connect worked and I was able to update K-line and enhanced drb3. So I changed the date to the correct date. Windows update also errored because of the wrong date. Try to use flexnet connect to update but it failed.
#Drb3 emulator install#
In the beginning when installing the stubs, his directions had already instructed you to change the date to 1/1/17, then navigate to the folder and install the three stubs. In order to get it to work, I had to change the date. Steps to DRB3 Emulator on Win7/Win10: Connect the microPod II device that will be used with Enhanced DRB III Emulator to a Windows computer that has the wiTECH Diagnostic Application (wiTECH 1.
I had to change it up since I did follow his instructions exactly, but the flexnet update didn’t work, and so it failed and te drb3 did not work. Anyway I will have to contact the seller and arrange for some discount since the hard drive is virtually useless.Īnyway, the main thing is that the miocropod had the required circuits etc, and the DRB3 works after following most of Radius’s instructions. I was able to make a backup though and there is actually a second partition on it with an Acronis backup image already created from 8/15/17. Its making beeping sounds and clicking and on its very last legs. It came with a hard drive that is barely working. I bought my micropod from the same seller Radius bought his from.
When green LED turns on, turn on car ignitionĢ4: When Windows is done installing drivers, etc, you should show a network connection in the tool tray with no internet accessĢ6: Press “Launch DRB III” button in lower right hand cornerīy following the above instruction, one user share his good experience: Do NOT update WiTech!!!ġ6: Flexnet will find updates for enhanced DRB and K-LineĢ0: Once updates and downloaded and installed, turn OFF internet and NEVER turn on again!Ģ2: Attach Micropod to car. Option 1: Bought MicroPod 2 from one Chinese Seller:ġ: Make a backup copy of the partition from the hard drive included with the micropod!ģ: Set date to 01/01/17 BEFORE booting from laptopĥ: Allow windows to install drivers, etc, as needed for your laptop and reboot as needed.Ħ: Once all of that is done, do NOT run WiTech yet!Ĩ: Navigate to C:\ProgramData\wiTECH\jserver\data\core\stubsġ5: Run Flexnet software updater. These are the steps I followed to use MicroPod 2 Clone to get Enhanced DRB III Emulator to work: